![]() Those are used to test interface rx/tx operations on GigabitEthernet (1gbit/sec) interfaces. If you want to use your plug on appliances from other manufacturers too, that maybe need a higher throughput during testing, it may be needed to create an eight pin self-loopback plug. This is the simpliest version of a four pin self-loopback plug which is used to test interface rx/tx operations on FastEthernet (100mbit/sec) interfaces. In the case of the FortiGate HQIP test, it’s already enough to connect the following conductor wires: pin 1 pin 3 You just need a RJ45 connector or an Ethernet cable with a RJ45 connector attached. It is very easy to create a self-loopback cable or connector plug by yourself. In comparison to normal “loopback” links, where one NIC is connected with another NIC on the same appliance, the self-loopback does realize the loopback inside the same NIC. Those cables are often descibed as selfloop or interface test cables. Įven though the name “self-loopback” is for some people a bit confusing, this is a very common and standardized wiring method for testing copper based ethernet equipment. Please restore factory reset or use port mode to perform the test WARNING: This test can only pass with factory configurations. This request looks like the following CLI output: Network Interface Loopback Test - Please connect ethernet cables: ![]() neighbor - The neighbor LACP information.On some FortiGate models, you are being asked to connect a self-loopback cable on some ports during the HQIP test. internal - The internal LACP information. By default, it is empty, and will displa y the information of all LACP groups. detail - The detailed information of EtherChan nel.Ģ5 Parameter channel-group-num - The EtherChannel G roup number, ranging from 1 to 6. By default, it is empty, and will displa y the information of all EtherChannel Groups. Global Configuration Mode : In this mode, global commands are provided, such as the Spanning Tree, Schedule Mode and so on.ħ 1.4 Conventions 1.4.1 Format Conventions The following conventions are used in this Guide: Items in square brackets are optional Items in braces Parameter channel-group-num - The EtherChannel G roup number, ranging from 1 to 6. To configure some commands, you should access the corres ponding command mode firstly. Each command mode has its own set of s pecific commands. Mode Accessing Path Prompt Logout or Access the next mode User EXEC Mode Primary mode once it is connected with the swi tch.Ħ 2. #Loopback cable config how to#T ype the User name and Passwo rd (the factory default value fo r both of them is admin) and press the Enter button, then you can use the CLI now, which is shown as Figure1-4.ĥ The following table gives detailed information about the Accessing path, Prompt of each mode and how to exit the current mode and access the next mode. T ype telnet 192.168.0.1 in the command prompt shown as Figure 1-3, and press the Enter button. T o log on to the switch by a T elnet connection, please take the following steps: 1.Ĥ 4. Chapter 12: Ethernet Configuration Commands Provide information about the commands used for configuring the Bandwidth Control, Negotiation Mode, and S torm Control for enthernet ports.ģ Chapter 1 Using the CLI 1.1 Accessing the CLI Y ou can log on to the switch and access the CLI by logging on to the switch remotely by a T elnet through an Ethernet port. #Loopback cable config upgrade#The four devices of TL-SG2216/TL-SG2424/TL-S G2424P/TL-SG2452 are sharing this Guide.Ģ IP, reboot and reset the switch, upgrade the sw itch system and comm ands used for device diagnose, including loopback test and cable test. The device mentioned in this Guide stands for TL-SG2216/TL-SG2424 /TL-SG2424P/TL-SG2452 Gigabit Smart Switch. ġ Preface This Guide is intended for network administrator to provide referenced information about CLI (Command Line Interface). 170 show lldp neighbor-infor mation inte rface. ![]() X show lldp local-inform ation inte rface. VII Chapter 1 8 DHCP Filteri ng Comma nds. Other brands and product names are trademarks or registered trademarks of t heir respective holders. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. I COPYRIGHT & TRADEMARKS S pecifications are subject to change without notice.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |